Niron content - HWzone Forums
Skip to content
  • Create an account


registered user
  • Number of messages

  • Join

  • Recently visited

Everything published by niron

  1. I guess you mean enable / disable. In the current situation, consider that there may be a situation where there is a chance that the PCIe connection is not working properly, if you turn off the internal screen (disable) and the connection to the external display is not working properly - there will be no display at all and the board will not be usable until you remove the battery. The board and reset the BIOS settings (will return the view back to the screen of the board). for your consideration.
  2. That there is no case unrelated and unaffected. If not connected properly to the end and in a stable way certainly can affect.
  3. (In principle this setting should work) What options are there besides auto?
  4. Check if there is a display setting in the BIOS (reserved for the computer to mount from a graphics card of the board - internal \ onboard graphics or from an external video card). If not then it is very possible that the PCIe connection on the board is not working properly.
  5. Do not disconnect (internal) hardware while the computer is running, you may burn the component and other components!
  6. There are a few options that you should check before disqualifying the board: 1. It is indeed possible that the PCIe connection is not working properly. 2. What power supply do you have? Did you check that it is suitable for the card in terms of power consumption and that it is working properly? Have you tried connecting another power supply? Does the card have an unconnected Pcie6 / 8 connector port? 3. Did you try to disconnect the VGA (blue) cable connected to the board and see if the screen shows a display from the card after booting? 4. Did you try to replace an HDMI cable and check other connections on the screen / card? One of these connections may be incorrect. 5. Has the hard disk been new or had it already been on a previous operating system with a driver / driver of a screen before you connected the card? If so, was the previous driver removed with DDU software via safe mode and was an updated Nvidia driver installed?
  7. First of all, you need to understand whether this is a hardware problem (keyboard or faulty keys) or a software problem (drivers / office / other contents or operating system). What operating system do you have? What is meant by each format? Did you try to uninstall and reinstall the office? Any copy paste operation fails or only in specific software? Does this also happen to you in normal copying of files in the operating system? Have you tried connecting another mouse / keyboard to the same computer, rebooting and seeing if it comes back? It could also be that one of the improper mouse / keyboard drivers and removal and reinstallation will fix the problem. 1. Try restarting the computer first and see if it comes back. 2. If it comes back - replace keyboard + mouse, restart the computer and see if it happens again. *** If you have already checked the office software (uninstalled and reinstalled) and saw that the problem is not there - 3. If it comes back - there could very well be a problem with the mouse / keyboard drivers or the operating system files were damaged, then do the following: 3.1 The search will write CMD and run as administrator - 3.2 In the black window that opens, type sfc / scannow and press the ENTER key. It will run a system file health check. At the end you will see if he writes that he found damaged files and if he repaired or not.
  8. Suggests that you contact Dell Support and open a call about it: 1809444693 will ask you for the Service Tag code (usually found on the bottom of your laptop). They will check if the computer is still under warranty and if necessary they may also replace a component (depending on their test).
  9. First try connecting to a different dimm (memory slot) - of course the computer should be turned off while replacing the slot. Go through them all one by one (maybe in one of the others it will come up). One of the reasons for a black screen on startup is a memory failure. If there is still no display, it could very well be that the memory module model you bought is not supported / not properly supported by the board. Try to replace the memory module. Of course there is a possibility that the cable you connected from the computer to the monitor is defective
  10. Look if it's detected in BIOS, it could very well be a faulty disk. Turn off the computer. Disconnect and reconnect (try replacing the SATA cable and / or port on the board). Restart and see if it comes back. Try the same test on another computer if you have one. Check Disk Management to see if it is possible to change the status of the disk from Offline to Online. If the fault recurs it is probably a disk fault.
  11. Before reinstalling, check to see if you have UEFI / Legacy modes in the BIOS. If so - check if changing the different SATA controller modes (IDE / AHCI / RAID) in both UEFI mode and Legacy will cause the operating system to go up. You should try running windows repair \ startup repair (do you have 10 or 7?) With the installation disk of the operating system installed, most of the time it does not work - sometimes yes. You can try to fix the references when the computer starts up on the boot via CMD from the installation disk: bootrec / fixmbr bootrec / fixboot bootrec / rebuildbcd but even this does not always work. In any case, before reinstalling the operating system (if you install) - back up the information that is important to you from the disk. Connect it as an additional disk to another computer and copy the information you need to an on-key disk or an external backup disk.
  12. A logical option, but it seems complicated for him to test. Requires someone with knowledge (technician / system person).
  13. PXE should not be relevant to the issue in this case. Usually PXE is a referral to migration from the network from a specific address (for example, an enterprise work environment from a domain, such as an installation server or terminal) and is not relevant to a home network. At most it will come down to the fact that it will delay the boot time until it switches to the next boot device. First of all, you should check out the steps suggested by jackhammer (can take time and you should linger and perform properly to rule out or find the source). If after the tests the problem is not resolved, in the absence of information there are a few more things to rule out: Is the MODE SATA CONTROLLER MODE configured as IDE / AHCI / RAID ???? Changing the setting of the controller from what it was when it was installed from the operating system can cause the operating system audio to not go up (usually defined as an IDE on older computers or AHCI). 1. Could it be that some of the system partition (UEFI partition) partitions are on the IDE disk outside the boot order? (Sometimes if there is more than one hard disk some of these partitions are physically defined on a disk other than the one on which drive C is installed). Try to return the IDE disk to boot order in different locations in ascending order and see if it goes up. If not, return outside the boot order as the image you attached. 2. As a last option, you can always return the BIOS settings to the default (load default), if you do not manually set a specific ascension order. In some cases this solves the problem. *** Note that if you have changed settings in the BIOS (other than ascension order), if you do not remember or are not sure what and how - do not rush to change to the default because later redefine (without knowledge) can be problematic and can do more harm than good.
  14. Different panels (and manufacturers) will allow access to the BIOS through different buttons, so I asked. In general: To enter BIOS via function key Turn the PC on. The PC screen displays the Lenovo logo. Immediately and repeatedly press (Fn +) F2 or F2 or via F1 key. Accessing the BIOS may take multiple attempts.
  15. which computer do you have? (Desktop / mobile) If mobile - which model? If desktop, what board model do you have?
  16. Do you know what happened before (any error message, Windows update, power outage)? Did you check that the hard disk is detected in the BIOS and is set to boot order?
  17. If it is an old computer, before contacting the manufacturer, you should check: 1. If the SATA port you connected to the board (and the SATA cable) are indeed sata3 and not sata2, because then the read / write speeds will indeed be significantly reduced. 2. In BIOS / UEFI controller sata controller mode is not defined as IDE but as AHCI. ** Note that if you have already installed an operating system, changing the controller mode will cause the operating system audio to not go up, and must be reinstalled, or alternatively return to the previous state. 3. The SSD firmware update may resolve the issue.
  18. According to the source of the problem you wrote, it seems that the problem is with the driver of the screen - Nvidia (nvlddmkm.sys). Download the DDU software (to remove the driver of the screen), go into safe mode and remove it from there with the software. Then reinstall and see if it comes back. If so - it could be due to a problem with the Diver itself (problematic version) or the installed version of the download is not suitable. If the problem occurs again, if you have a previous installation that worked, try installing it and see if it comes back Things to check: 1. Have you checked that the driver you downloaded is suitable? 2. What games do you play and in what settings? (Maybe the processor / c. The screen does not meet the graphic requirements and / or the page does not meet the warming and power consumption) 3. You are connected to an external screen Or uses a laptop screen? (If so, 1080 or 4k screen?) 4. Did it work properly in the games before reinstalling? Another option is to run a benchmark test that will check the card performance under effort, while checking temperatures.
  19. Check with CrystalDiskMark software. The 840 is a SATA disk, which is limited to 560 megabytes. The 970 EVO is an NVME that is far above the speeds of the 840.
  20. none77 Thanks for the help. EVGA response: Attaches for those who plan to buy a 3090 card when the card has 3 pcie connections (instead of 2). The Corsair power supply model they are talking about is SF750 It is not possible to use the card with just two 6 + 2pin connectors as all three connections would need to be powered and it is not recommended to use an adapter to split the connections to power two as it would double the load on the single cable. Since all three connections need to be powered it would not run. If you can change the power supply that has three connections it would be safe however it would not work with just two connections. If the power supply in the enclosure takes standard SF power supplies then you can change it however reviewing the Corsair power supply it only has two power cables with the 4 connections so you would have to share a cable between two connections which is not recommended as it could cause stability issues. Please note that the non-FTW3 versions of the card have just two power connections so if you where to go to a non-FTW3 version it would work in the case as-is. Regards, EVGA
  21. thank you for the quick reply. As for the alternative power - should be for the Razer Core X enclosure which is actually egpu and not a desktop computer case. According to the egpu forum the dimensions of the power so that it fits the Razer Core X enclosure should be 88mm x 151mm x 142mm: Jumping in late to the response, however I noticed that most of the commercially available PSUs, especially those that would offer higher wattages or gold / titanium ratings tend to be too big to install as a drop-in replacement for the Core X. Unless you are willing to remove the bracket that holds the 120mm case fan, you will need to find a PSU that has the following dimensions +/- 1mm (I used a metric tape measure) 88mm x 151mm x 142mm If you exceed the 88mm depth by too much, you will bump into the PCB board inside the Core X If you exceed the 142mm depth, you will have to remove the fan bracket <- This is your most likely limiting factor ** If you exceed the 151mm depth, you are ok as there is still room between the top of the PSU and the Core X's outer enclosure -cables / replacement-psu-razer-core-x / The question of whether it is worth giving up the 120mm internal fan in favor of a frame supplier The limitations of the dimensions in egpu, when many reviews of the 3090 card say that it produces a lot of heat.
  22. Hello everyone, the above video card has three 2 + 6/8 pin connections, but the Razer stock has only 2 2 + 6 pin cables (the power is not modular). This means that only 2 of the 3 connections on the video card can be connected . The Razer website states that the EGPU supports the 30 Series (at the bottom of the page): Compatible NVIDIA® graphics chipsets: Geforce ™ RTX 30 Series ? __ cf_chl_jschl_tk __ = 4c3f5ea074b4ee5147b1920cb3fc3a142a32741d-1609421719-0-AcaGOtO8Jiwl2R2maWyCr-k-VkwipXNH4BUi7nrz-yw9lbr4Dt6gfICHKgt8zaX3IPOqIMJxTyMwNVOPP8u5iCTwDSKp7yFgo3QQlyd9RF1dBkRajrJBAoLua82B5DCZje0GX26OwM0qhsg1IqiovsVVeuynBpnMDi4I1aWkjynmvMKvMKNHYnWvr8kUmJmTbjFiV5_I_J38Dh5S-yFe-6ovuPHURczAhVhMxF25Fk6-cAlCQlcJJbFpAOvXQWEBCBsOwyu-ZSLMxfMRSkNT5Zf5DX9Uuplkfpsk1ZRRxFGP30Fh2AIbugncK0XXvT6VBLKkfjoK1QK5iPsun-3AQHXS7VLK77rzQ-OxKHRKQKh1bN8aQwMpaJuYmslwGR1flZxl2oWd8sDDhTGQ8NR-O8rl2Z-5BPWPxGegCtrsaH6k EVGA's product page reads: Requirements Minimum of a 750 Watt power supply. Three available 8-pin or 6 + 2pin PCIe power dongles Total Power Draw: 350 Watts I guess they refer to a computer configuration Complete (board, processor, memories, storage, etc.) and not for a single card configuration in egpu enclosure. In a review of the card on the techpowerup website we noted that the power consumption of the card reaches around 500W: My questions are: 1. As I mentioned, is it possible to use only 2 2 + 6 pin connections (instead of 3 connections), even though apparently the card requires 3 connections for stable voltage? 2. If there are only 2 connections instead of 3, does this limit the card's capabilities, and to what extent? 3. And most importantly - is it safe? I prefer not to invest in replacing an expensive supplier that will fit the dimensions of this egpu, if the stock supplier can meet the power consumption requirements without any danger (say of the connector flare due to the load). If so, which vendor do you recommend replacing (of course according to Core x dimensions). I read of the Corsair SF750 there is a problem with 3080 3090 cards: In the EVGA forum most commenters wrote that only 3 connections should be connected (and not 2) and that a supplier needs to be replaced. In other forums some have written that if you connect only 2 they may shower due to the load - I do not know how much it is based and this is an important point - hence the question. I contacted both Razer and EVGA but have not yet received a response from any source. I would appreciate your assistance. Nir
  • Create new ...

At the top of the news:

new on the site